Gas alarm system based on Arduino, MQ-4 sensor and SSD1306 screen

Arduino UNO 07-04-24

204 0

Tutorial plan

Introduction

1- How the gas alarm system ordered by Arduino UNO works ?

2- Mounting Arduino UNO board with MQ-4 sensor, LED, Buzzer and SSD1306 screen

3- Program Arduino UNO to control the system

Introduction

A gas alarm system is a safety device designed to detect the presence of potentially harmful gases in an environment, such as carbon monoxide (CO), natural gas, propane, methane, or other combustible gases. These systems are commonly used in homes, commercial buildings, industrial facilities, and other locations where gas leaks could pose a threat to health and safety.

Here's how a typical gas alarm system works:

1- Gas Sensors: Gas alarm systems contain sensors that are capable of detecting specific types of gases. These sensors continuously monitor the air for the presence of gases, and when they detect a gas at a certain concentration level, they trigger an alarm.

2- Alarm Devices: When a gas is detected, the system activates alarm devices such as sirens, strobe lights, or audible alerts to warn occupants of the building about the potential danger. These alarms are usually loud and conspicuous to ensure they can be easily heard or seen.

3- Monitoring and Notification: In some cases, gas alarm systems are connected to monitoring services that can provide remote monitoring and notifications. This allows for immediate response in case of a gas leak, even if no one is present at the location where the alarm is installed.

4- Integration with Building Systems: Advanced gas alarm systems may be integrated with other building systems, such as ventilation systems or shut-off valves for gas lines. This integration allows for automated responses to gas leaks, such as activating ventilation to remove the gas from the building or shutting off the gas supply to prevent further leaks.

5- Maintenance and Testing: Regular maintenance and testing of gas alarm systems are essential to ensure their proper functioning. This includes periodic calibration of sensors, testing of alarm devices, and replacing batteries or other components as needed.

Overall, gas alarm systems play a crucial role in preventing accidents and protecting occupants from the dangers associated with gas leaks. They provide early warning of potential hazards, allowing people to take appropriate actions to mitigate the risks and ensure their safety.

How the gas alarm system ordered by Arduino UNO works ?

Gas alarm systems play a crucial role in detecting and alerting users to the presence of hazardous gases in an environment. This gas alarm system utilizes an Arduino UNO microcontroller, an MQ-4 gas sensor, an SSD1306 screen, an LED indicator, and a buzzer to provide real-time gas monitoring and alarm notifications.

Components:

1- Arduino UNO:

Arduino Uno

The Arduino UNO serves as the central processing unit, responsible for controlling the sensor readings, processing data, and triggering alarm signals.

2- MQ-4 Gas Sensor:

The MQ-4 sensor is designed to detect various combustible gases such as methane, natural gas, and propane. It provides analog output proportional to the gas concentration in the surrounding atmosphere.

3- SSD1306 screen

The SSD1306 is a popular display controller used in OLED (Organic Light-Emitting Diode) screens. It's commonly employed in various electronics projects to showcase information on small screens. The SSD1306 controller is compatible with different screen sizes and is often integrated with microcontrollers like Arduino UNO board to display text, graphics, and images.

The SSD1306 screen is used to display the alert message in case of gas leak detection.

4- LED Indicator:

An LED indicator serves as a visual alert, signaling the presence of hazardous gas when the concentration exceeds a predefined threshold.

5- Buzzer:

A piezoelectric buzzer generates audible alarm signals to alert users to potential gas leaks or unsafe conditions.

Working Principle:

1- Initialization: Upon power-up, the Arduino UNO initializes the components, including the MQ-4 sensor, SSD1306 screen, LED, and buzzer.

2- Gas Detection: The MQ-4 sensor continuously samples the surrounding air for the presence of combustible gases. It converts the gas concentration into an analog voltage signal.

3- Data Processing: The Arduino reads the analog voltage from the sensor and converts it into a gas concentration value using calibration factors or conversion formulas.

4- Display Output: The gas concentration value is displayed on the SSD1306 screen in real-time, allowing users to monitor gas levels visually.

5- Alarm Triggering: If the gas concentration exceeds a predefined threshold considered unsafe, the Arduino triggers alarm signals. The LED indicator lights up, and the buzzer emits audible alarm sounds to alert users to potential hazards.

6- Continuous Monitoring: The system continuously loops through these steps, providing continuous gas monitoring and alarm notifications.

Features:

1- Real-time Monitoring: The gas alarm system offers real-time monitoring of gas concentration levels, enabling users to respond promptly to hazardous conditions.

2- Threshold Alarm: The system triggers visual and audible alarms when the gas concentration exceeds a predefined threshold, ensuring timely warnings to prevent accidents.

3- User Interface: The SSD1306 screen provides a user-friendly interface for displaying gas concentration readings and alarm messages, enhancing user interaction and understanding.

4- Multimodal Alerts: The system employs both visual (LED) and audible (buzzer) alarm signals, increasing the likelihood of alerting users in noisy or visually challenging environments.

5- Customization: The system can be customized by adjusting threshold levels, calibration parameters, and alarm settings to suit specific gas detection requirements.

6- Low-Cost Solution: Utilizing readily available components and open-source Arduino software, the gas alarm system offers a cost-effective solution for gas detection and safety monitoring applications.

Mounting Arduino UNO board with MQ-4 sensor, LED, Buzzer and SSD1306 screen

Attaching the MQ-4 sensor :

- Connect the VCC pin of the MQ-4 sensor to the 5V pin of the Arduino UNO board

- Connect the GND pin of the MQ-4 sensor to the GND pin of the Arduino UNO board

- Connect the DO pin of the MQ-4 sensor to the A0 pin of the Arduino UNO board

Attaching the buzzer :

- Connect the (+) terminal of buzzer to pin 5 of the Arduino UNO board.

- Connect the (-) terminal of buzzer to GND pin of the Arduino UNO board.

Attaching the red LED :

- Connect the negative terminal (cathode) of LED to the ground (GND) of the Arduino UNO board.

- Connect the positive terminal (cathode) of LED to pin 4 of the Arduino UNO board.

Attaching the SSD1306 Display :

- Connect the SDA (data line) of the SSD1306 display to A4 pin of Arduino UNO board.

- Connect the SCL (clock line) of the SSD1306 display to A5 pin of Arduino UNO board.

- Connect the VCC pin of the SSD1306 display to the 5V pin of Arduino UNO board.

- Connect the GND pin of the SSD1306 display to GND pin of Arduino UNO board.

Program Arduino UNO to control the system

Below is an example code to program the gas alarm system based on Arduino UNO, MQ-4 sensor, SSD1306 screen, LED, and Buzzer:

import this library : Adafruit_SSD1306 for SSD1306 display

#include <Adafruit_SSD1306.h>

//OLED   define
#define SCREEN_WIDTH 128 // OLED display width, in pixels
#define SCREEN_HEIGHT   64 // OLED display height, in pixels
// Declaration for an SSD1306 display connected   to I2C (SDA, SCL pins)
Adafruit_SSD1306 display(SCREEN_WIDTH, SCREEN_HEIGHT,   &Wire, -1);

int buzzer_pin = 5; // Digital pin for Buzzer 
int redled_pin = 4; // Digital pin for LED 
int analogPin = A0; // Analog pin for MQ-4 sensor 
int analogVal; //analog readings 

<span class="hljs-type">const</span> <span class="hljs-type">int</span> threshold = <span class="hljs-number">300</span>; <span class="hljs-comment">// Threshold value for triggering alarm</span>

void setup() {

  if(!display.begin(SSD1306_SWITCHCAPVCC, 0x3C))   { // Address 0x3D for 128x64
    Serial.println(F("SSD1306 allocation failed"));
     for(;;);
  }
  display.display(); //Display logo
  delay(1000); 
  display.clearDisplay();
   
  Serial.begin(9600);
  pinMode(buzzer_pin, OUTPUT); 
  pinMode(redled_pin, OUTPUT);
  
}
void loop () {
  analogVal = analogRead(analogPin); // Read analog value from MQ-4 sensor
  Serial.print("gaz= ");
  Serial.print(analogVal);
  // Read the analog interface
  if (analogVal<=threshold) // If the sensor detects a gas leak
  { // print alert message on SSD1306 screen
   display.setTextSize(2);
   display.setTextColor(WHITE);
   display.setCursor(0, 0);
   display.print("Attention!");
   display.setCursor(0, 28);
   display.print("detect Gas");
   display.display();
   // Turn on LED and Buzzer
    digitalWrite(buzzer_pin, HIGH); 
    digitalWrite(redled_pin, HIGH);
  }
  else {
    display.clearDisplay(); // clear the SSD1306 display
    display.display(); 
    // Turn off LED and Buzzer
    digitalWrite(buzzer_pin, LOW); 
    digitalWrite(redled_pin, LOW); 
  }
  delay(100); 
  }

#include <Adafruit_SSD1306.h>

//OLED define

#define SCREEN_WIDTH 128 // OLED display width, in pixels

#define SCREEN_HEIGHT 64 // OLED display height, in pixels

// Declaration for an SSD1306 display connected to I2C (SDA, SCL pins)

Adafruit_SSD1306 display(SCREEN_WIDTH, SCREEN_HEIGHT, &Wire, -1);

int buzzer_pin = 5; // Digital pin for Buzzer

int redled_pin = 4; // Digital pin for LED

int analogPin = A0; // Analog pin for MQ-4 sensor

int analogVal; //analog readings

const int threshold = 300; // Threshold value for triggering alarm

void setup() {

if(!display.begin(SSD1306_SWITCHCAPVCC, 0x3C)) { // Address 0x3D for 128x64

Serial.println(F("SSD1306 allocation failed"));

for(;;);

}

display.display(); //Display logo

delay(1000);

display.clearDisplay();

Serial.begin(9600);

pinMode(buzzer_pin, OUTPUT);

pinMode(redled_pin, OUTPUT);

}

void loop () {

analogVal = analogRead(analogPin); // Read analog value from MQ-4 sensor

Serial.print("gaz= ");

Serial.print(analogVal);

// Read the analog interface

if (analogVal<=threshold) // If the sensor detects a gas leak

{ // print alert message on SSD1306 screen

display.setTextSize(2);

display.setTextColor(WHITE);

display.setCursor(0, 0);

display.print("Attention!");

display.setCursor(0, 28);

display.print("detect Gas");

display.display();

// Turn on LED and Buzzer

digitalWrite(buzzer_pin, HIGH);

digitalWrite(redled_pin, HIGH);

}

else {

display.clearDisplay(); // clear the SSD1306 display

display.display();

// Turn off LED and Buzzer

digitalWrite(buzzer_pin, LOW);

digitalWrite(redled_pin, LOW);

}

delay(100);

}

This program continuously reads the analog value from the gas sensor, converts it into a gas concentration value, and displays it on the SSD1306 screen. If the gas concentration exceeds the predefined threshold, an alarm is triggered, which includes turning on an LED and sounding a buzzer for a specified duration.

Make sure to adjust the threshold value and the conversion function according to the specifications of your MQ-4 gas sensor and the gases you want to detect. Additionally, consider calibrating the sensor in a controlled environment for accurate readings.